Exactly How to Remove and Change a Tub
Exactly How to Remove and Change a Tub
Blog Article
Just how do you really feel about How to Install a Bathtub Yourself?
Installing a tub isn't specifically rocket science, however it does call for solid plumbing, carpentry, as well as occasionally, tiling skills. Replacing an old tub with a brand-new one is also a moderately tough task. If the old tub is easily easily accessible, the task can relocate quickly; if you have to open up a wall surface to get rid of the old bathtub and also place the brand-new bathtub, the task is much harder. In either case, the project is within a home handyman's skills, although you will require a helper to move out the old tub as well as set in the new one. Ensure you have qualified yourself for the job and are comfortable attempting it. Rather than hiring a professional to take over a halfway-completed project, it is far better to take into consideration using one before you begin. Chances are you may need a professional plumber to make tube connections.
This short article will assist you set up a new bathtub in your bathroom if you have currently acquired a brand-new bathtub as well as don't need to transform the setup of your previous water supply pipes.
Your tools and also product checklist ought to make up the following:
Removing Old Taps
If you need to replace old taps with new ones as a part of your installation, after that the first thing you need to do is separate the water. After doing so, activate the faucets to drain any type of water remaining in the system. The process of getting rid of the existing faucets can be rather troublesome due to the limited accessibility that is commonly the situation.
Utilize a basin wrench (crowsfoot spanner) or a tap device to reverse the nut that links the supply pipes to the taps. Have a towel prepared for the staying water that will come from the pipelines. When the supply pipes have been gotten rid of, utilize the same tool to loosen up the nut that holds the taps onto the bath/basin. You will require to quit the single faucets from transforming during this process. As soon as the taps have been gotten rid of, the holes in the bath/basin will certainly have to be cleansed of any kind of old sealing substance.
Before going on to fit the new faucets, compare the pipeline connections on the old faucets to the new faucets. If the old taps are longer than the brand-new taps, after that a shank adapter is required for the brand-new taps to fit.
Suitable New Taps
If the tails of the new faucets are plastic, then you will certainly need a plastic adapter to avoid damages to the string. One end of the connector fits on the plastic tail of the faucet and the various other end offers a link to the existent supply pipelines.
If you need to fit a monobloc, after that you will need lowering couplers, which links the 10mm pipeline of the monobloc to the basic 15mm supply pipeline.
Next, position the tap in the placing hole in the bath/basin ensuring that the washing machines are in location between the faucet and the sink. Protect the tap in position with the manufacturer supplied backnut. Once the tap is firmly in place, the supply pipelines can be linked to the tails of the faucets. The taps can either be attached by using corrugated copper piping or with regular tap ports. The former type should be linked to the faucet finishes first, tightening up just by hand. The supply pipes can later on be connected to the other end. Tighten both ends with a spanner after both ends have actually been attached.
Installing the Tub
Making use of both wood boards under its feet, place the tub in the called for setting. The wood boards are helpful in uniformly spreading out the weight of the bathtub over the location of the boards as opposed to focusing all the weight onto four tiny points.
The next objective is to make certain that the bathtub is leveled all round. This can be accomplished by examining the spirit level as well as readjusting the feet on the bathtub until the level reviews degree.
To install taps, fit all-time low of the outermost flexible tap port to the ideal supply pipe by making a compression join; after that do the very same for the various other tap.
Turn on the water system and also check all joints and new pipework for leakages and also tighten them if essential. Fill the bathtub and likewise examine the overflow electrical outlet and the normal outlet for leaks.
Lastly, take care of the bath paneling as explained in the producer's instruction manual. Tiling as well as sealing around the tub ought to wait up until the tub has been used at least once as this will settle it right into its last placement.
Planning for the Installment
To start with, the sustaining framework supplied with the bath should be fitted (if required) according to the manufacturer's guidelines. Next off, fit the faucets or mixer to the bathtub. When fitting the faucet block, it is important to ensure that if the tap includes a plastic washer, it is fitted between the bath and the taps. On a plastic bath, it is additionally reasonable to fit a sustaining plate under the faucets system to prevent strain on the bath tub.
Fit the versatile tap connectors to the bottom of both faucets utilizing 2 nuts and olives (sometimes provided with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet hole, and then pass the electrical outlet via the hole in the bathroom. Utilize the nut supplied by the manufacturer to fit the plug-hole. Examine the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next, fit the end of the flexible overflow pipeline to the overflow electrical outlet. Afterwards, screw the pipeline to the overflow face which must be fitted inside the bath. See to it you utilize all of the provided washing machines.
Connect the catch to the bottom of the waste outlet on the bathtub by winding the string of the waste outlet with silicone mastic or PTFE tape, and also screw on the catch to the outlet. Link the bottom of the overflow tube in a comparable manner.The bathroom ought to currently prepare to be fitted in its final placement.
Tiling Around the Tub
In the area where the bathroom satisfies the tile, it is essential to secure the joins with a silicone rubber caulking. This is necessary as the installation can move sufficient to split a rigid seal, creating the water to permeate the wall surface in between the bath and also the tiling, resulting in complications with wetness and feasible leaks to the ceiling listed below.
You can select from a selection of coloured sealants to assimilate your fixtures as well as fittings. They are offered in tubes and also cartridges, as well as can sealing spaces approximately a width of 3mm (1/8 inch). If you have a bigger gap to load, you can fill it with spins of soaked paper or soft rope. Remember to constantly fill the bath tub with water before securing, to allow for the activity experienced when the tub remains in use. The sealer can crack relatively early if you do not take into consideration this movement prior to sealing.
Additionally, ceramic coving or quadrant tiles can be utilized to border the bath or shower tray. Plastic strips of coving, which are easy to use as well as reduce to size, are likewise conveniently available on the market. It is a good idea to fit the floor tiles using water-resistant or water-proof glue and grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
I am very excited about How to Install a Bathtub and I'm hoping you liked my post. Those who enjoyed reading our blog posting please don't forget to share it. Bless you for your time. Kindly pay a visit to our blog back soon.
Book An Estimate Now
Report this page